Strutural analysis in
Hi everyone,I was just working on structural analysis with the help of Creo 2.0 parametric , did anyone know how to put ball & pin constraint on surface or a point.Which are the best tools to be...
View ArticleStep File Viewer
Hi All, We are currently using Creo 2.0 in a marine environment. We would like to give our shop floor staff access to the models we produce (in .stp format ideally) so that they are able to view them...
View ArticleCan't edit dimensions in Creo 2.0. Please help
I've lost the ability to double click on a dimenions and type in the desired value. Please help!!!If I draw a simple rectangle in sketcher and then hit Select, the dimensions will show up. But when I...
View Articlehow to mirror a extrude of text in the part model?
Dear Everyone, I just extrude a text in the part file and when i mirror it ,you know what happen. is anyway to make it correct? Manish
View ArticleControlling pipe orientation?
How can I control the orientation of my pipes (both spec / non-spec)? When I route a line, e.g. through a datum point array, the pipeline seems to rotate by 90 degrees at some (but not all?) bends....
View ArticleHow to create a profile like attached image in pro/e sheetemetal
How to create a profile like attached image in pro/e sheetemetal
View ArticleClik here to view.
Upgrading Pro/E. creo1, creo2? What is recommended?
We are on WF5/creo. Hate it. Thinking of upgrading, possibly all the way to creo2. What are you guys suggesting? Should we go all the way to creo2? Is the latest date code good, or is there a...
View Articlecreo 2: drawing layers missing items compared to model layers
ok, so i have assembly "A" which goes into assemble "B", and i have a drawing for assembly "B". my layers are correct in assembly "A" and assembly "B", but when i go to the drawing for assembly "B" i...
View ArticleClik here to view.
Help modeling a rasp with offset teeth
Creo is still relatively new to me. I am trying to model a curved rasp-like surface with rows of staggered teeth. However, I cannot figure out how to reasonably create the teeth profile. In Creo I have...
View ArticleClik here to view.
Creo 2 Upgrade to M100 for students ?
Hey, i use PTC Creo 2.0 Student Edition (mainly Parametric) on my Laptop with Windows 8.1. I have Creo 2 M070 but it takes about 3 minutes to load and I have problems with some operations. I have read,...
View ArticlePossible to gather multiple point data in a csv file in WF5?
I am attempting to generate the x-y coordinate data around a close curve (one curve generated from a family tree). In WF 5, I can march through Analysis, Geometry, Point which gives me the x y point...
View ArticleNo he podido completar la instalación de Creo 2.0
Hola!He tenido un problema al intalar el creo 2.0, cada vez que completo la instalación y lo abro para comenzar a trabajar aparece una página de servicion de creo pero al tratar de abrir el espacio de...
View ArticleSurface from datum points in WF3
I have a set of datum points taken from a table that shows position and height over base ground level.How can I create a surface through these points?
View ArticleMechanism dynamics tutorials
Hi, I require mechanism dynamics tutorials can anyone tell me where i can get it. RegardsSamuel
View ArticleHow to control line space in a ptc font?
We want to use the leroy font for some signs we're manufacturing. But since the heigt of the leroy font is defined wrong (when you set the text height to 5mm, the lowercase letter turms out 5mm high)...
View Articlenot able to install creo 2.0 on network?
not able to install creo 2.0 on network? I have installed Creo 2.0 on the main computer, but when i try to install it on other computer connected to the network it says licence unavailable. other then...
View ArticleClik here to view.
Sketch to drawing
I have made a cut in the model, see image.In the drawing I would like to use the construction circle diameter 70 to show where the 3 small holes are located.I would also like to show the mid axis of...
View ArticleCustom symbols in drawing
i had created a custom symbol and used in the current drawing sheet,but how should i open those symbols in the other drawing sheet?
View Articledrafting question
Can you draft walls in creo-2 that have radii on them without taking off the radii? I have a dummy part we got from a customer and it has a lot of ribs on it and they all have radius on them. They...
View ArticleDrawing in Creo Schematics
I am new to Creo Schematics. I went through the LMS tutorials and got 94% on the assessment. Now, I'm trying to generate my first live schematic. I have the library of IEEE symbols from Virtual...
View Article